Manual pipeline strainers Installation Manual
2026-05-29Traffic：
Manual pipeline strainers Installation Steps Manual:
Preparation:
Confirm that the filter's specifications and model meet the system design requirements.
Check that the filter packaging is intact, all accessories are present, and there is no obvious damage.
Prepare the required installation tools, such as wrenches, gaskets, bolts, nuts, etc.
Location Selection:
Choose an appropriate installation location, typically installed upstream of the equipment to be protected (such as pumps, valves, instruments, etc.), ensuring that the fluid passes through the Manual pipeline strainers before entering downstream equipment.
Ensure the installation location allows for routine maintenance and cleaning/replacement of the filter basket.
Piping Connection:
Connect the inlet and outlet water pipes of the Manual pipeline strainers to the corresponding flange interfaces, noting that the water flow direction should be consistent with the rib indication on the basket filter shell.
Use new gaskets and tighten the flange connection bolts according to the specified torque value.
Support and Fixing:
If necessary, provide dedicated supports or hangers for large or high-pressure basket filters to ensure the equipment does not vibrate or shift during operation.
Valve Settings:
Install valves near the inlet and outlet of the filter to facilitate cutting off the water flow during later maintenance, cleaning, or replacement of the filter basket.
It is recommended to equip bypass piping and valves to ensure the entire system can operate normally during cleaning or replacement of the filter basket.
System Flushing:
Before the first use, flush the entire system to remove impurities and debris from the pipes.
Open the valves upstream and downstream of the filter, allowing the fluid to pass through the filter slowly, and check for leaks.
Operation Monitoring:
Start the system operation, observe the working condition of the Manual pipeline strainers, and record initial pressure drop data.
Develop Manual pipeline strainers cleaning or replacement plan based on actual conditions.
Maintenance:
Regularly open the basket filter to clean or replace the filter basket according to system operating conditions and pressure drop changes.
When cleaning or replacing the filter basket, ensure the system is in a pressure-free state and comply with relevant safety operating procedures.
Finally, always strictly follow the official manual provided by JOECHRE Environmental Protection, the manufacturer of the Manual pipeline strainers for installation and operation to ensure the safe and effective operation of the equipment.
Preparation:
Confirm that the filter's specifications and model meet the system design requirements.
Check that the filter packaging is intact, all accessories are present, and there is no obvious damage.
Prepare the required installation tools, such as wrenches, gaskets, bolts, nuts, etc.
Location Selection:
Choose an appropriate installation location, typically installed upstream of the equipment to be protected (such as pumps, valves, instruments, etc.), ensuring that the fluid passes through the Manual pipeline strainers before entering downstream equipment.
Ensure the installation location allows for routine maintenance and cleaning/replacement of the filter basket.
Piping Connection:
Connect the inlet and outlet water pipes of the Manual pipeline strainers to the corresponding flange interfaces, noting that the water flow direction should be consistent with the rib indication on the basket filter shell.
Use new gaskets and tighten the flange connection bolts according to the specified torque value.
Support and Fixing:
If necessary, provide dedicated supports or hangers for large or high-pressure basket filters to ensure the equipment does not vibrate or shift during operation.
Valve Settings:
Install valves near the inlet and outlet of the filter to facilitate cutting off the water flow during later maintenance, cleaning, or replacement of the filter basket.
It is recommended to equip bypass piping and valves to ensure the entire system can operate normally during cleaning or replacement of the filter basket.
System Flushing:
Before the first use, flush the entire system to remove impurities and debris from the pipes.
Open the valves upstream and downstream of the filter, allowing the fluid to pass through the filter slowly, and check for leaks.
Operation Monitoring:
Start the system operation, observe the working condition of the Manual pipeline strainers, and record initial pressure drop data.
Develop Manual pipeline strainers cleaning or replacement plan based on actual conditions.
Regularly open the basket filter to clean or replace the filter basket according to system operating conditions and pressure drop changes.
When cleaning or replacing the filter basket, ensure the system is in a pressure-free state and comply with relevant safety operating procedures.
Finally, always strictly follow the official manual provided by JOECHRE Environmental Protection, the manufacturer of the Manual pipeline strainers for installation and operation to ensure the safe and effective operation of the equipment.
Previous: Installation method of Manual pipeline strainer
Nextpage: The function and use of Manual pipeline strainers
